So i made use of a 元 switch configure 2 ports (port 1 and port 2) both access with the same vlan id. Now here is the real problem, before i even start to create both device to join SSO / HA, With a Single 3504 the management interface when i apply Vlan ID in CLI mode immediately my laptop connection to this mention WLC 3504 (Which is correct because my laptop does not carry VLAN id). I have 2 unit of WLC 3504 with are in the same firmware which are now in SSO mode (as all you may know in order to join SSO / HA for both of this unit need to be in the same VLAN id) That are untagged, or that have an 802.I'm having trouble with my current WLC 3504 with the latest firmware from Cisco (8.5.120). It's going to be long story but i'll try to make it less boring as possible.
VLAN MEDIA CONVERTER HOW TO
The following example shows how to configure the native VLAN of a 1/0/33 trunk interface as 1. Same value at both ends of the link, or traffic can be lost or sent to the wrong VLAN. The native VLAN must be configured with the The native VLAN cannot be configured on a subinterface of the trunk interface. Is the VLAN to which all the untagged VLAN packets are logically assigned. The dot1q vlan native command defines the default, or native VLAN, associated with an 802.1Q trunk interface. That user group assignment is preventing you from using a command, contact your AAA administrator. To use this command, you must be in a user group associated with a task group that includes proper task IDs. Interface configuration (config-if) Command History No default behavior or values Command Modes Specifies the native VLAN associated with the 802.1Q trunk interface.
No dot1q vlan vlan-id Syntax Description vlan-id To remove the VLAN ID assignment, use the no form of this command. To assign the native VLAN ID of a physical interface trunking 802.1Q VLAN traffic, use the dot1q vlan native command in interface configuration mode. This example shows how to display debug messages for VTP redundancy: Device> enableĭevice# debug sw-vlan vtp redundancy dot1q vlan native To debug a specific stack member, youĬan start a CLI session from the active switch by using the session switch stack-member-number privileged EXEC command. When you enable debugging on a switch stack, it is enabled only on the active switch. VTP_PRUNING_LOG_ALERT, and VTP_PRUNING_LOG_WARNING macros in the VTP pruning code. They are generated by the VTP_PRUNING_LOG_NOTICE, VTP_PRUNING_LOG_INFO, VTP_PRUNING_LOG_DEBUG, If no additional parameters are entered after the pruning keyword, VTP pruning debugging messages appear. The undebug sw-vlan vtp command is the same as the no debug sw-vlan vtp command. Layer to send, except for pruning packets.
VLAN MEDIA CONVERTER CODE
(Optional) Displays debug messages for the contents of all outgoing VTP packets that the VTP code requests the Cisco IOS VTPĭisplays debug messages for VTP redundancy.ĭisplays debug messages for the contents of all outgoing VTP packets that the VTP code requests the Cisco IOS VTP platform-dependent (Optional) Displays debug messages for the contents of all incoming VTP pruning packets that have been passed into the VTPĬode from the Cisco IOS VTP platform-dependent layer. IOS VTP platform-dependent layer, except for pruning packets.ĭisplays debug messages generated by the pruning segment of the VTP code.
To disable debugging, use the no form of this command.ĭebug sw-vlan ĭisplays debug messages for general-purpose logic flow and detailed VTP messages generated by the VTP_LOG_RUNTIME macro inĭisplays debug messages for the contents of all incoming VTP packets that have been passed into the VTP code from the Cisco
To enable debugging of VLAN manager activities, use the debug sw-vlan command in privileged EXEC mode. You can verify that information was deleted by entering the show vtp counters privileged EXEC command. This example shows how to clear the VTP counters: Device> enable This command has no arguments or keywords. To clear the VLAN Trunking Protocol (VTP) and pruning counters, use the clear vtp counters command in privileged EXEC mode.
0 kommentar(er)
